ELOG - 2026-03_raris

1

Anonymous (anonymous@undisclosed.example.com) — 2026-02-28T06:01:49+00:00

Type: General Category: General Tags: Subject: stage manual stage manual ステージのマニュアル * 画像右奥のPCからxystage(10.30.40.30) Ver.2.viを起動 * 上部の表示ボタンで現在のステータスを表示 * コイル励磁ONボタンで励磁

2

Anonymous (anonymous@undisclosed.example.com) — 2026-02-28T16:53:40+00:00

Type: General Category: Setup Tags: ReplyTo: 1 Subject: Re: stage manual Re: stage manual Current Beam table stage height: -76531 It would be better to keep the power on to place it on the same height.

3

Anonymous (anonymous@undisclosed.example.com) — 2026-03-01T01:36:37+00:00

Type: General Category: General Tags: Subject: Daily meeting note (2.28) Daily meeting note (2.28) 九大のセンサーの動作確認 * 事前の試験 * SMU * オシロ * Sr * LV * 明日、全数確認する。 * DUTで試験を予定。

4

Anonymous (anonymous@undisclosed.example.com) — 2026-03-01T07:29:54+00:00

Type: General Category: Setup Tags: Subject: IP and connection methods for numerous PCs, HV, LV and Oscilloscope IP and connection methods for numerous PCs, HV, LV and Oscilloscope ▶︎ ここに今回のTestBeamで使用するPC, HV, LV, Oscilloscopeのipやアクセスの仕方と関係をまとめる。

5

Anonymous (anonymous@undisclosed.example.com) — 2026-03-01T11:46:16+00:00

Type: General Category: General Tags: Subject: Daily meeting note (3.1) Daily meeting note (3.1) 中川＋川出 * SMUx2 * PCx2 * Wave Runner x1 * KEKの忘れもの * 信州大のPC * KEKの備品を持って来ていた * 理研の高電圧電源

6

Anonymous (anonymous@undisclosed.example.com) — 2026-03-02T14:31:20+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: RFSoC error RFSoC error RFSoC を ./tmux_rf.sh で起動時、rf01のみ起動に失敗(rf02-05は起動)。bin/rfdcbabies.elf 10 9 0 に失敗している。

7

Anonymous (anonymous@undisclosed.example.com) — 2026-03-02T04:26:28+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: RFSoC software: current status RFSoC software: current status ・rf01が動かない　（前ログ参照）・GTR: KEKでは不調と聞いていたが、/usr/gto ディレクトリが存在していなかったので、 install & make を再度実行した　→　直った

8

Anonymous (anonymous@undisclosed.example.com) — 2026-03-02T06:18:31+00:00

Type: Test Category: Beam3_RFSoC Tags: Subject: Data taking test: sampling rate limit Data taking test: sampling rate limit first take input rate -> Sampling rate (30s) 1.3kHz -> 1.3kHz 13kHz -> 3.7kHz 130kHz -> 3.9kHz

9

Anonymous (anonymous@undisclosed.example.com) — 2026-03-02T06:31:40+00:00

Type: Test Category: Beam3_RFSoC Tags: ReplyTo: 8 Subject: Re: Data taking test: sampling rate limit Re: Data taking test: sampling rate limit 1Gbps second take (with file size) input rate → Sampling rate (30sec) : (file size) 1.31kHz → 39,240 / 30 = 1.308kHz : (499MB)

10

Anonymous (anonymous@undisclosed.example.com) — 2026-03-02T07:02:09+00:00

Type: Test Category: Beam3_RFSoC Tags: ReplyTo: 9 Subject: Re: Data taking test: sampling rate limit Re: Data taking test: sampling rate limit 10Gbps first take input rate → Sampling rate (30sec) : (file size, #RunNum) *1.31kHz → 37,152 / 30 = 1.238kHz : (473MB, #15)

11

Anonymous (anonymous@undisclosed.example.com) — 2026-03-02T07:20:43+00:00

Type: Test Category: Beam3_RFSoC Tags: ReplyTo: 10 Subject: Re: Data taking test: sampling rate limit Re: Data taking test: sampling rate limit 10Gbps second take input rate → Sampling rate (30sec) : (file size, #RunNum) 3.30kHz → 90,529 / 30 = 3.018kHz : (1.2GB, #19)

12

Anonymous (anonymous@undisclosed.example.com) — 2026-03-02T08:16:24+00:00

Type: Test Category: Beam3_RFSoC Tags: ReplyTo: 11 Subject: Re: Data taking test: sampling rate limit Re: Data taking test: sampling rate limit 1Gbps third take (change cat6 cable) input rate → Sampling rate (30sec) : (file size, #RunNum) 1.31kHz → 39,229 / 30 = 1.308kHz : (499MB, #22)

13

Anonymous (anonymous@undisclosed.example.com) — 2026-03-02T08:51:11+00:00

Type: Test Category: Beam3_RFSoC Tags: ReplyTo: 12 Subject: Re: Data taking test: sampling rate limit Re: Data taking test: sampling rate limit 10Gbps third take (change cat6 cable) input rate → Sampling rate (30sec) : (file size, #RunNum) 3.51kHz → 96,635 / 30 = 3.221kHz : (1.2GB, #26)

14

Anonymous (anonymous@undisclosed.example.com) — 2026-03-02T14:30:46+00:00

Type: General Category: Beam3_RFSoC Tags: ReplyTo: 7 Subject: Re: RFSoC software: current status Re: RFSoC software: current status getesevtnumber のイベント数の不一致を修正しました現在の不具合：rf01が動かない

15

Anonymous (anonymous@undisclosed.example.com) — 2026-03-02T14:42:50+00:00

Type: General Category: General Tags: Subject: sensor alignment sensor alignment sensor position center Axis1 , Axis2 , Axis3 71500, 71000, 70750

16

Anonymous (anonymous@undisclosed.example.com) — 2026-03-02T14:44:22+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: Scintillator setup for RFSoC Scintillator setup for RFSoC scintillatorにかけるHV電圧, 電流-電圧比小 (東大CNS): 900V, I/V = 19uA /100V 大 (つくば) : 1100V, I/V = 27uA /100V

17

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T02:21:20+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV (Keithley SMU) IP address HV (Keithley SMU) IP address 上段：IP = 192.168.0.25 下段：IP = 192.168.0.26 Internal gateway (RFSoC DAQ PC)：192.168.0.1 Global IP of RFSoC DAQ PC：10.30.1.150

18

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T00:39:34+00:00

Type: General Category: Setup Tags: ReplyTo: 4 Subject: Re: IP and connection methods for numerous PCs, HV, LV and Oscilloscope Re: IP and connection methods for numerous PCs, HV, LV and Oscilloscope Additional IP addresses: * RFSoC DAQ PC (msqd02): 10.30.1.150 (external), 192.168.0.1 (internal)

19

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T00:59:29+00:00

Type: General Category: Setup Tags: Subject: Re: IP and connection methods for numerous PCs, HV, LV and Oscilloscope (2026-03-03-09:54) Re: IP and connection methods for numerous PCs, HV, LV and Oscilloscope (2026-03-03-09:54) * DUTに接続していたWavePro２台（4ch x 2 = 8ch）を、一台のWaveRunner（#6）に取り替え、IPも設定した。

20

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T03:29:06+00:00

Type: General Category: Setup Tags: Subject: Find the number of Segments that will makes SaveTime optimal Find the number of Segments that will makes SaveTime optimal * RARiSのビームの1サイクルがActive (10s) → Non-active (20s)なので、Non-active (20s)中にActive (10s) で観測したdataを保存したい

21

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T05:55:26+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: RFSoC current status: 3/3 AM RFSoC current status: 3/3 AM 3/3昼時点の状況：・安定したデータ取得が可能になりました (operation manual は別途) ・4列50um センサーが不調のため、取り外しました (2列30umのみデータ取得)

22

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T05:56:42+00:00

Type: Standard Run Category: Beam3_RFSoC Tags: Subject: Run 41 start Run 41 start Run 41 を開始 (2列30umセンサー１枚のみ)

23

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T06:41:37+00:00

Type: General Category: Setup Tags: Subject: Trigger Delay Trigger Delay * EUDAQ ID#2 ip:192.168.0.102 → 65 ns * EUDAQ ID#3 ip:192.168.0.103 → 91 ns * EUDAQ ID#4 ip:192.168.0.104 → 86 ns * EUDAQ ID#5 ip:192.168.0.105 → 90 ns * EUDAQ ID#6 ip:192.168.0.106 → 90 ns

24

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T07:28:46+00:00

Type: Standard Run Category: Beam3_RFSoC Tags: ReplyTo: 22 Subject: Re: Run 41 start Re: Run 41 start Run 41 end 585738 events / 86 min = 114Hz (filesize:19.52 GB)

25

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T11:38:26+00:00

26

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T07:45:05+00:00

Type: Standard Run Category: Beam3_RFSoC Tags: Subject: HV change: 185 V → 180 V HV change: 185 V → 180 V HV 電流値が limit (1 uA) に達した。DUT の温度上昇によって電流が増大したと思われる。そのため、Run 43 以降では HV 電圧値を

27

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T10:13:07+00:00

Type: Error/Fault Category: General Tags: Subject: Bug found in the sequence mode Bug found in the sequence mode The bug was related to the “batch” mode, which is turned on when we use the number of segements configuration over 1k segments. Under debuging now, while taking the data with 500 segments (less efficiency)

28

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T11:14:02+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: RFSoC operation manual RFSoC operation manual Line 3 (RFSoC) のシフト時のマニュアル (簡易版) を以下のスライドに共有します適宜更新予定基本操作は * ブラウザの SMU operation (

29

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T11:20:49+00:00

Type: General Category: General Tags: Subject: AC-LGAD Sensor IV curve AC-LGAD Sensor IV curve This is the sensor's IV curve. Measurement up to the voltage or current limit.

30

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T14:34:09+00:00

Type: Standard Run Category: Beam3_RFSoC Tags: Subject: HV Scan case150V HV Scan case150V * #Run：46 * Start：2026-03-03-19:15:40 * Stop：2026-03-03-19:41:56 * 電流値：約-0.117 uA * 電圧値：-149.998 V * イベント数：

31

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T11:39:10+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: RFSoC shifter schedule: 3/3 RFSoC shifter schedule: 3/3 3/3 のシフトでやること：HV scan (HV の電圧を変えながらデータ取得) (DUT: AC-LGAD 4columns 30um) * 150 V - 185 V まで、5 V 刻みで (

32

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T13:02:59+00:00

Type: General Category: General Tags: Subject: Change vertical position Change vertical position vertical position change ? → -51631

33

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T13:52:26+00:00

Type: General Category: General Tags: ReplyTo: 32 Subject: Re: Change vertical position Re: Change vertical position -51631 → -72631

34

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T15:45:47+00:00

Type: Standard Run Category: Beam3_RFSoC Tags: Subject: HV Scan case155V HV Scan case155V * #Run：51 * Start：2026-03-03-23:58:33 * Stop：2026-03-04-00:43:13 * 電流値：約-0.137 uA * 電圧値：-149.998 V * イベント数：

35

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T16:03:09+00:00

Type: General Category: Setup Tags: Subject: LGAD05 move LGAD05 move 5mm up

36

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T16:03:58+00:00

Type: General Category: Setup Tags: Subject: Move Scint.trigger 1 +x Move Scint.trigger 1 +x Move Move Scint.trigger 1 towards +x 2mm

37

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T23:05:13+00:00

Type: Standard Run Category: Beam3_RFSoC Tags: ReplyTo: 34 Subject: Re: HV Scan case155V Re: HV Scan case155V * #Run：52 and 53（不採用） * Events = 0 * tmuxのrefreshにより解消 * 大村はミスっているが、バグった後のtestには

38

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T16:52:04+00:00

Type: General Category: Setup Tags: Subject: Detector movement for alignment Detector movement for alignment * Trigger -> move both -3mm (Y) - reason: missing shadow in LGAD01, DUT bottom (~2mm) * LGAD05 -> move +5mm (Y) -> reason: table height +5mm showed the best cross-section

39

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T17:02:58+00:00

Type: General Category: Setup Tags: Subject: Move table up +3mm Move table up +3mm reason: -3mm movement of the trigger

40

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T17:10:20+00:00

Type: General Category: Setup Tags: ReplyTo: 38 Subject: Re: Detector movement for alignment Re: Detector movement for alignment Move LGAD05 -7mm (Y) -> reason: we move both trigger and LGAD in opposite direction (+5,-3) so it was actually moved 8mm up. originally, it was a little bit below the beam so we decided to move it down -7 mm (Y)

41

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T17:27:39+00:00

Type: General Category: Setup Tags: ReplyTo: 40 Subject: Re: Detector movement for alignment Re: Detector movement for alignment * LGAD05 -> -2mm (reson: no signals in upper side 2mm, could be related to the trigger) * LGAD02 -> 1mm (reason: no signals in ch0 region (~2mm), so we decide to move it 1mm first)

42

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T17:42:59+00:00

Type: General Category: Setup Tags: ReplyTo: 41 Subject: Re: Detector movement for alignment Re: Detector movement for alignment * LGAD01: -0.6mm * LGAD02: 0.3mm * LGAD05: -0.5mm

43

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T18:07:26+00:00

Type: General Category: Setup Tags: ReplyTo: 36 Subject: Re: Move Scint.trigger 1 +x Re: Move Scint.trigger 1 +x Move scint. trigger 1(LGAD01) to +1.0mm since we moved LGAD01 -1.6mm

44

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T18:16:13+00:00

Type: General Category: Setup Tags: ReplyTo: 39 Subject: Re: Move table up +3mm Re: Move table up +3mm Move table -5 mm (Y)

45

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T18:38:02+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: RFSoC channel and DUT sensor channel correspondence RFSoC channel and DUT sensor channel correspondence RFSoC が各チャンネルで読み出しているセンサーについて 3/3ビーム開始〜現在、RFSoC 1台 (8ch) につき、4ch を１枚目センサー、4chを２枚目センサーの読み出しに使用している

46

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T23:04:35+00:00

Type: Standard Run Category: Beam3_RFSoC Tags: ReplyTo: 37 Subject: HV Scan case160V HV Scan case160V * #Run：55 * Start：2026-03-04-01:36:21 * stop：2026-03-04-01:41:41 * 電流値：約-0.155 uA * 電圧値：-160.000 V * イベント数：

47

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T20:53:37+00:00

Type: Standard Run Category: Beam3_RFSoC Tags: ReplyTo: 46 Subject: HV Scan case165V HV Scan case165V * #Run：63 * Start：2026-03-04-04:03:00 * Stop：2026-03-04-04:03:27 * 電流値：約-0.179 uA * 電圧値：-164.997 V * イベント数：

48

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T20:36:40+00:00

Type: General Category: General Tags: Subject: beam stop beam stop 5:30, beam was stoped by accelerator trouble. but beam recovery soon

49

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T21:59:16+00:00

Type: Standard Run Category: Beam3_RFSoC Tags: ReplyTo: 47 Subject: HV Scan case170V HV Scan case170V * #Run：65（不採用） * Start：2026-03-04-05:22:05 * stop：2026-03-04-05:32:08 * 電流値：約-0.207 uA * 電圧値：-169.998 V

50

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T23:11:22+00:00

Type: Standard Run Category: Beam3_RFSoC Tags: ReplyTo: 49 Subject: HV Scan case175V HV Scan case175V * #Run：67 * Start：2026-03-04-06:45:11 * Stop：2026-03-04-07:55:23 * 電流値：約-0.245 uA * 電圧値：-174.998 V * イベント数：

51

Anonymous (anonymous@undisclosed.example.com) — 2026-03-03T23:25:11+00:00

Type: Standard Run Category: Beam3_RFSoC Tags: ReplyTo: 50 Subject: HV Scan case180V HV Scan case180V * #Run：68 * Start：2026-03-04-08:07:24 * Stop：2026-03-04-08:23:28 * 電流値：約-0.295 uA * 電圧値：-179.995 V * イベント数：

52

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T01:47:52+00:00

Type: Standard Run Category: Beam3_RFSoC Tags: ReplyTo: 51 Subject: Re: HV Scan case180V Re: HV Scan case180V * #Run : 69 * daq bug -> miss * #Run : 70 * Start : 2026-03-04-09:40:30 * Stop : 2026-03-04-10:35:44 * 電流値 : 約-0.299 uA

53

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T05:53:59+00:00

Type: Shift Summary Category: General Tags: Subject: Day Shift Program Day Shift Program Following is the program for this monring: --- DUT( 2Col,50um) x-Position Scan --- * Keep the Trigger Rates from the current run as the reference. ~10Hz (screenshot in

54

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T08:55:05+00:00

Type: General Category: General Tags: Subject: DUT (2col,50um) x-Position scan DUT (2col,50um) x-Position scan 9:30 The coincidence trigger rates are dropped from 10Hz to 8Hz after the trigger counter-2 relocation work. This drop is minor enought, so we'll move on to the position scan program without adjusting its alignment.

55

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T01:26:34+00:00

Type: Error/Fault Category: Beam3_RFSoC Tags: Subject: Time lag Time lag There was a time lag between the actual time and the time on the RFSoCDAQPC. From this point onward, we will use the RFSoCDAQPC time as the reference.

56

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T01:47:00+00:00

Type: Standard Run Category: Beam3_RFSoC Tags: Subject: HV Scan case 185V HV Scan case 185V A new log was created by mistake. Please refer to the other one for the run information.

57

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T06:02:15+00:00

Type: Standard Run Category: Beam3_RFSoC Tags: ReplyTo: 52 Subject: Re: HV Scan case185V Re: HV Scan case185V * #Run : 71 * Start : 2026-03-04-10:50:10 * Stop : 2026-03-04-12:02:22 * 電流値 : 約0.371 uA * 電圧値 : -184996 V *

58

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T02:59:35+00:00

Type: General Category: General Tags: Subject: DUT position scan early tests DUT position scan early tests Double-checking strip planes orientation, as in the picture of the blackboard. DUT has horizontal strips which means that automatic X-scanning is parallel to the strips. Taking a scan anyway with -+6, -+3, 0, the rate should drop but the channel configuration should not change

59

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T06:01:21+00:00

Type: Standard Run Category: Beam3_RFSoC Tags: ReplyTo: 57 Subject: Re: HV Scan case185V Re: HV Scan case185V * #Run : 72 * Start : 2026-03-04-12:10:22 * Stop : 2026-03-04-12:31:20 * 電流値 : 約0.371 uA * 電圧値 : -184.996 V *

60

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T03:14:37+00:00

Type: Error/Fault Category: Beam3_RFSoC Tags: ReplyTo: 55 Subject: Re: Time lag Re: Time lag The START and STOP times were correct, so the time lag does not need to be considered.

61

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T04:04:36+00:00

Type: Standard Run Category: Beam3_RFSoC Tags: ReplyTo: 59 Subject: Re: HV Scan case185V Re: HV Scan case185V * #Run : 73 * Start : 2026-03-04-12:34:59 * Stop : 2026-03-04-12:53:05 * 電流値 : 約0.372 uA * 電圧値 : -184.996 V *

62

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T04:38:58+00:00

Type: Standard Run Category: Beam3_RFSoC Tags: ReplyTo: 61 Subject: Re: HV Scan case190V Re: HV Scan case190V * #Run : 74 * Start : 2026-03-04-12:55:34 * Stop : 2026-03-04-13:29:18 * 電流値 : 約0.485 uA * 電圧値 : -189.997 V *

63

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T05:06:17+00:00

Type: Standard Run Category: Beam3_RFSoC Tags: ReplyTo: 62 Subject: Re: HV Scan case190V Re: HV Scan case190V * #Run : 75 * Start : 2026-03-04-13:38:02 * Stop : 2026-03-04-14:02:39 * 電流値 : 約0.486 uA * 電圧値 : -189.997 V *

64

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T04:50:35+00:00

Type: General Category: General Tags: Subject: Front PMT (trigger) Front PMT (trigger) The PMT trigger in front of L0 AC-LGAD has been moved up roughly by 1mm.

65

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T05:47:53+00:00

Type: General Category: General Tags: Subject: Trigger, Tracker, DUT fine tune alignment Trigger, Tracker, DUT fine tune alignment * Optimization for the measurement: 13:45 Adjusted tigger counter-1 by 1mm. The trigger rates dropped from 8Hz to 3Hz.

66

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T05:01:25+00:00

Type: General Category: General Tags: Subject: DUT module DUT module The DUT AC-ALGAD module has moved up by roughly 1 mm.

67

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T05:15:30+00:00

Type: Standard Run Category: Beam3_RFSoC Tags: ReplyTo: 63 Subject: Re: HV Scan case195V Re: HV Scan case195V * #Run : 76 * Start : 2026-03-04-14:03:10 * Stop : 2026-03-04-14:14:16 * 電流値 : 約0.680 uA * 電圧値 : -194.998 V *

68

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T05:25:12+00:00

Type: General Category: General Tags: Subject: Back PMT (Trigger) Back PMT (Trigger) The PMT trigger in the back AC-LGAD module has been moved up roughly by 1mm.

69

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T06:00:03+00:00

Type: Standard Run Category: Beam3_RFSoC Tags: ReplyTo: 67 Subject: Re: HV Scan case195V Re: HV Scan case195V * #Run : 77 * Start : 2026-03-04-14:22:11 * Stop : 2026-03-04-14:46:16 * 電流値 : 約0.683 uA * 電圧値 : -194.998 V *

70

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T06:50:30+00:00

Type: Standard Run Category: Beam3_RFSoC Tags: ReplyTo: 69 Subject: Re: HV Scan case195V Re: HV Scan case195V * #Run : 78 * Start : 2026-03-04-14:56:43 * Stop : 2026-03-04-15:38:01 * 電流値 : 約0.683 uA * 電圧値 : -194.998 V *

71

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T06:39:19+00:00

Type: General Category: General Tags: Subject: Data process error for Run#103152115 Data process error for Run#103152115 We have error to process data Run#103152115. “Error decodeing block 0 in Event 5693: buffer size must be a multiple of element size.

72

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T17:10:49+00:00

Type: Standard Run Category: Beam3_RFSoC Tags: ReplyTo: 70 Subject: Re: HV Scan case199V Re: HV Scan case199V * #Run : 79 * Start : 2026-03-04-15:39:48 * Stop : 2026-03-04-16:51:19 * 電流値 : 約0.973 uA * 電圧値 : -198.996 V *

73

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T09:18:51+00:00

Type: General Category: General Tags: Subject: DUT (2col,50um) x-Position scan (Take-2) DUT (2col,50um) x-Position scan (Take-2) Take-2 horizontal scan with 2Col50um to cover whole acceptance of the DUT. -6, -9, -12, -6, -3, 0, +3, +6, -6mm Based on the attached results, the provisional center is now defined as x=70,000 (-2mm of nominal position so far).

74

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T08:10:16+00:00

Type: General Category: General Tags: Subject: Some tracking residual plots Some tracking residual plots Reconstruction with CorryVreckan and tracking of run103053608_260304072319.root Y residual make sense because of 3 planes (2 planes + DUT) but X residual is only two point. Track is alway perfect and we cannot evaluate alignment.

75

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T08:15:47+00:00

Type: General Category: General Tags: Subject: Improved clustering corryvreckan Improved clustering corryvreckan improved clustering using corryvreckan, with threshold of 10mV for seed and 5mV for secondaries. left is with high threshold, which reconstructs mostly single strips. With improved clustering the position distribution is more flat as expected (except at edges because it doesn't have further strips)

76

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T08:59:09+00:00

Type: General Category: General Tags: Subject: March 4th Daily meeting minutes March 4th Daily meeting minutes Line-2 Report: * Coarse horizontal scan of 2Col50um sensor is ongoing. Will optimize the center position after the scan. * We will swap the trigger counter-1 fixture once Kentaro produces new parts using 3D printer. Needs alignment again after this.

77

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T09:07:00+00:00

Type: Standard Run Category: Beam3_RFSoC Tags: ReplyTo: 72 Subject: Re: HV Scan case199V Re: HV Scan case199V * #Run : 80 * Start : 2026-03-04-17:15:07 * Stop : 2026-03-04-17:58:33 * 電流値 : 約0.974 uA * 電圧値 : -198.996 V *

78

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T10:20:27+00:00

Type: Error/Fault Category: Beam3_RFSoC Tags: Subject: HV1(192.168.0.25)電流limit HV1(192.168.0.25)電流limit HV1(192.168.0.25)が、HV100Vで0.999uA(limit)に達したため、DUT1(4col 30umは)98.39Vで運用

79

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T10:24:05+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: DUT change DUT change DUT change 変更前　DUT1：無し　DUT2：2col 30um 変更後　DUT1：4col 30um　DUT2：4col 50um(穴無し)

80

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T10:29:20+00:00

Type: Error/Fault Category: General Tags: Subject: 照射室の照明を消灯照射室の照明を消灯 19:20頃、ビーム照射室の電気がついていたため、消灯した。

81

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T10:29:31+00:00

Type: Error/Fault Category: Beam3_RFSoC Tags: ReplyTo: 78 Subject: Re: HV1(192.168.0.25)電流limit Re: HV1(192.168.0.25)電流limit 電気を直したらこのバグは直りましたので、HVを150Vまで上げました。

82

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T10:35:16+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV Scan case150V HV Scan case150V * #Run : 81 * Start : 2026-03-04-19:07:50 * Stop : 2026-03-04-19:25:17 * HV1 * 電流値 : 約1.0 uA * 電圧値 : -100 V * HV2 * 電流値：約

83

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T12:05:06+00:00

Type: General Category: Beam3_RFSoC Tags: ReplyTo: 82 Subject: Re: HV Scan case150V Re: HV Scan case150V * #Run : 82 * Start : 2026-03-04-19:27:12 * Stop : 2026-03-04-20:53:42 * HV1 * 電流値 : 約53.4 nA * 電圧値 : -149.997 V

84

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T12:09:57+00:00

Type: General Category: Beam3_RFSoC Tags: ReplyTo: 83 Subject: Re: HV Scan case180V Re: HV Scan case180V * #Run : 83 * Start : 2026-03-04-21:00:21 * Stop : 2026-03-04-21:01:29 * HV1 * 電流値 : 約0.1 uA * 電圧値 : -180 V *

85

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T13:00:38+00:00

Type: General Category: Beam3_RFSoC Tags: ReplyTo: 84 Subject: Re: HV Scan case180V Re: HV Scan case180V * #Run : 84 * Start : 2026-03-04-21:01:41 * Stop : 2026-03-04-21:56:52 * HV1 * 電流値 : 約0.12 uA * 電圧値 : -179.996 V

86

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T14:36:57+00:00

Type: Error/Fault Category: General Tags: Subject: strange wive form strange wive form 21:23(103210022)にwave formが後ろにずれていく問題を発見した 3/3 19:30頃に探し始めた 22:58(102225816)までは大丈夫だったが、24:00頃(102235830)から問題が見られた

87

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T14:40:26+00:00

Type: Error/Fault Category: General Tags: ReplyTo: 86 Subject: Re: strange wive form Re: strange wive form Solved by removing 'timeout configuration from the run config. Detailed study should be done later but for the moment, we can take the data with long enough segment to reduce the beam loss. (~2500? 5000?)

88

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T14:42:40+00:00

Type: General Category: Beam3_RFSoC Tags: ReplyTo: 85 Subject: Re: HV Scan case180V Re: HV Scan case180V #Run : 85 Start : 2026-03-04-21:01:41 Stop : 2026-03-04-21:56:52 HV1 * 電流値 : 約0.119 uA * 電圧値 : -179.996 V HV2 * 電流値：約0.234 uA

89

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T15:15:26+00:00

Type: General Category: General Tags: Subject: Daily meeting note (3.3) Daily meeting note (3.3) 全体： * ビームを出し始めた九大のセンサーの動作確認 * 4列30umの電圧が掛からなかった * 3Vでダメ。コンディショニング？で100Vくらいまで行けたが、その後、掛からなくなった。

90

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T15:27:44+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-30um & 4col-50um-nohole, 195V HV scan: 4col-30um & 4col-50um-nohole, 195V #Run : 86 Start : 2026-03-05-00:15:37 Stop : 2026-03-05-00:19:38 HV 1 : 0.245 uA (195 V) HV 2 : 0.481 uA (195 V)

91

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T16:44:46+00:00

Type: General Category: Beam3_RFSoC Tags: ReplyTo: 90 Subject: Re: HV scan: 4col-30um & 4col-50um-nohole, 195V Re: HV scan: 4col-30um & 4col-50um-nohole, 195V #Run : 87 Start : 2026-03-05-00:27:15 Stop : 2026-03-05- HV 1 : 0.256 uA (195 V) HV 2 : 0.480 uA (195 V)

92

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T16:17:25+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: Onlinemonitor for QA Onlinemonitor for QA QA用の onlinemonitor を作成しました使い方: onlinemonitor xxxx (eg. Run 80 の場合、 0088) → DAQ PC からデータをシンクロさせた後、その run を

93

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T16:58:10+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: Re: HV scan: 4col-30um & 4col-50um-nohole, 195V Re: HV scan: 4col-30um & 4col-50um-nohole, 195V #Run : 88 Start : 2026-03-05-00:43:21 Stop : 2026-03-05-01:15:46 HV 1 (4col-30um) : 0.256 uA (195 V)

94

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T16:58:25+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: Re: HV scan: 4col-30um & 4col-50um-nohole, 195V Re: HV scan: 4col-30um & 4col-50um-nohole, 195V #Run : 89 Start : 2026-03-05-01:19:17 Stop : 2026-03-05-01:28:31 HV 1 (4col-30um) : 0.256 uA (195 V)

95

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T17:00:05+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: Re: HV scan: 4col-30um & 4col-50um-nohole, 195V Re: HV scan: 4col-30um & 4col-50um-nohole, 195V #Run : 90 Start : 2026-03-05-01:43:06 Stop : 2026-03-05-01:56:24 HV 1 (4col-30um) : 0.256 uA (195 V)

96

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T17:01:12+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: 3/4時点での QA script 進捗 3/4時点での QA script 進捗 datacp : DAQ PC から QA PC へ .ridf データを rsync で転送 * 実行時のディレクトリに関わらず、.ridf ファイル転送先のディレクトリが

97

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T22:03:52+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: Re: HV scan: 4col-30um & 4col-50um-nohole, 195V Re: HV scan: 4col-30um & 4col-50um-nohole, 195V #Run : 91 Start : 2026-03-05-03:51:11 Stop : 2026-03-05-04:00:29 HV 1 (4col-30um) : 0.257 uA (195 V)

98

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T20:03:34+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-30um & 4col-50um-nohole, 200V HV scan: 4col-30um & 4col-50um-nohole, 200V #Run : 92 Start : 2026-03-05-04:07:17 Stop : 2026-03-05-04:59:06 HV 1 (4col-30um) : 0.395 uA (200 V) HV 2 (4col-50um-nohole) : 0.720 uA (200 V)

99

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T21:54:11+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-30um & 4col-50um-nohole, 205V HV scan: 4col-30um & 4col-50um-nohole, 205V #Run : 93 Start : 2026-03-05-05:05:46 Stop : 2026-03-05-05:09:06 HV 1 (4col-30um) : 0.811 uA (205 V) HV 2 (4col-50um-nohole) : 1.36 uA (205 V)

100

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T21:54:28+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: Re: HV scan: 4col-30um & 4col-50um-nohole, 205V Re: HV scan: 4col-30um & 4col-50um-nohole, 205V #Run : 94 Start : 2026-03-05-05:16:39 Stop : 2026-03-05-05:26:50 HV 1 (4col-30um) : 0.811 uA (205 V)

101

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T21:54:46+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: Re: HV scan: 4col-30um & 4col-50um-nohole, 205V Re: HV scan: 4col-30um & 4col-50um-nohole, 205V #Run : 95 Start : 2026-03-05-05:33:38 Stop : 2026-03-05-06:17:24 HV 1 (4col-30um) : 0.810 uA (205 V)

102

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T21:54:58+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: Re: HV scan: 4col-30um & 4col-50um-nohole, 205V Re: HV scan: 4col-30um & 4col-50um-nohole, 205V #Run : 96 Start : 2026-03-05-06:24:05 Stop : 2026-03-05-06:43:55 HV 1 (4col-30um) : 0.810 uA (205 V)

103

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T21:59:49+00:00

Type: General Category: Setup Tags: Subject: Adjust trigger PMT threshold Adjust trigger PMT threshold Original: both ~35mV Updated: trigger1 (front) 177mV, trigger2(below) 154.5 mV Reason: reduce fake trigger + keep real coincidence

104

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T00:04:57+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-30um & 4col-50um-nohole, 205V HV scan: 4col-30um & 4col-50um-nohole, 205V #Run : 97 Start : 2026-03-05-06:46:44 Stop : 2026-03-05-07:00:27 HV 1 (4col-30um) : 0.811 uA (205 V) HV 2 (4col-50um-nohole) : 1.34 uA (205 V)

105

Anonymous (anonymous@undisclosed.example.com) — 2026-03-04T23:38:27+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-30um & 4col-50um-nohole, Current Max. HV scan: 4col-30um & 4col-50um-nohole, Current Max. #Run : 98 Start : 2026-03-05-07:29:45 Stop : 2026-03-05-08:36:01 HV 1 (4col-30um) : 1 uA (206 V)

106

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T01:03:28+00:00

Type: General Category: General Tags: Subject: HV scan: 4col-30um & 4col-50um-nohole, 203V HV scan: 4col-30um & 4col-50um-nohole, 203V currrent limit(1μA)に到達したので、limit付近のVを間隔を細かくして測定。 #Run : 99 Start : 2026-03-05-09:01:38

107

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T03:26:51+00:00

Type: General Category: General Tags: Subject: HV scan: 4col-30um & 4col-50um-nohole, 202V HV scan: 4col-30um & 4col-50um-nohole, 202V #Run : 100 Start : 2026-03-05-10:15:54 Stop : 2026-03-05-10:20:27 HV 1 (4col-30um) : 0.496uA (202 V) HV 2 (4col-50um-nohole) : 0.884uA (202 V)

108

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T07:01:43+00:00

Type: General Category: Beam3_RFSoC Tags: ReplyTo: 107 Subject: Re: HV scan: 4col-30um & 4col-50um-nohole, 202V Re: HV scan: 4col-30um & 4col-50um-nohole, 202V #Run : 101 Start : 2026-03-05-11:27:15 Stop : 2026-03-05-12:23:39 HV 1 (4col-30um) : 0.496uA (202 V)

109

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T03:55:22+00:00

Type: General Category: General Tags: Subject: Horizontal Scan for 2Cols30um started Horizontal Scan for 2Cols30um started 11:20 We have started the horizontal scan of 2Cols30um sensor at the operation HV of 197V. The pilot run shows nicely centered beam position at DUT in 0mm position.

110

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T02:48:25+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: 3/5 シフターのやることリスト 3/5 シフターのやることリスト上から順に HV scan: 現在のsetup (4col-30um & 4col-50um-穴なし) * 3/5 8:30 シフト終了時点で、{150V, 180V, 195V~} が終了しているので、155V-190V の残りを取得

111

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T07:01:30+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-30um & 4col-50um-nohole, 190V HV scan: 4col-30um & 4col-50um-nohole, 190V #Run : 102 Start : 2026-03-05-12:29:03 Stop : 2026-03-05-12:59:03 HV 1 (4col-30um) : 0.189uA (190 V) HV 2 (4col-50um-nohole) : 0.361uA (190 V)

112

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T05:06:04+00:00

Type: General Category: General Tags: Subject: Procedure for DUT(4Cols,30um) Preparation Procedure for DUT(4Cols,30um) Preparation Line-3: * Record drawing currents in line-3. * Shutoff all HV and LVs in line-3. * Disconnect all cables of 4Cols30um sensor and remove.

113

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T07:01:18+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-30um & 4col-50um-nohole, 185V HV scan: 4col-30um & 4col-50um-nohole, 185V #Run : 103 Start : 2026-03-05-13:00:21 Stop : 2026-03-05-13:12:06 HV 1 (4col-30um) : 0.149uA (185 V) HV 2 (4col-50um-nohole) : 0.288uA (185 V)

114

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T07:01:07+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-30um & 4col-50um-nohole, 175V HV scan: 4col-30um & 4col-50um-nohole, 175V #Run : 105 Start : 2026-03-05-13:20:19 Stop : 2026-03-05-13:32:01 HV 1 (4col-30um) : 0.102uA (175 V) HV 2 (4col-50um-nohole) : 0.203uA (175 V)

115

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T04:31:10+00:00

Type: General Category: General Tags: ReplyTo: 112 Subject: Re: Procedure for DUT(4Cols,30um) Preparation Re: Procedure for DUT(4Cols,30um) Preparation

116

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T07:00:55+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-30um & 4col-50um-nohole, 170V HV scan: 4col-30um & 4col-50um-nohole, 170V #Run : 106 Start : 2026-03-05-13:33:06 Stop : 2026-03-05-13:44:39 HV 1 (4col-30um) : 0.088uA (170 V) HV 2 (4col-50um-nohole) : 0.178uA (170 V)

117

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T07:00:45+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-30um & 4col-50um-nohole, 165V HV scan: 4col-30um & 4col-50um-nohole, 165V #Run : 107 Start : 2026-03-05-13:45:50 Stop : 2026-03-05-13:57:09 HV 1 (4col-30um) : 0.077uA (165 V) HV 2 (4col-50um-nohole) : 0.157uA (165 V)

118

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T07:00:29+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-30um & 4col-50um-nohole, 160V HV scan: 4col-30um & 4col-50um-nohole, 160V #Run : 108 Start : 2026-03-05-13:57:49 Stop : 2026-03-05-14:09:40 HV 1 (4col-30um) : 0.068uA (165 V) HV 2 (4col-50um-nohole) : 0.141uA (165 V)

119

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T05:22:48+00:00

Type: General Category: General Tags: Subject: Horizontal Scan for 2Cols30um finished Horizontal Scan for 2Cols30um finished Horizontal Scan for 2Cols30um finished. attached the plot of DUT&MCP-PMT_Efficiency VS. x-position(Axis2)

120

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T06:24:06+00:00

Type: General Category: General Tags: Subject: Mounted DUT(4Cols,30um) in line 2 Mounted DUT(4Cols,30um) in line 2 Changed DUT in line 2 to (4Cols,30um), which was first dismounted from line 3 Applied voltage in Line 2 is now 198V Line 3 now has (2Cols, 20um) mounted

121

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T07:25:52+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-20um, 120V & 4col-50um-nohole, 150V HV scan: 4col-20um, 120V & 4col-50um-nohole, 150V #Run : 109 Start : 2026-03-05-15:31:38 Stop : 2026-03-05-15:46:32 HV 1 (4col-20um) : 0.157uA (120 V)

122

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T06:49:10+00:00

Type: General Category: General Tags: Subject: Horizontal Scan for 4Cols30um started Horizontal Scan for 4Cols30um started Horizontal Scan for 4Cols30um started. channels correspond with strips like attached the image.

123

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T06:59:04+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: Mounted Sensor(4Cols,20um) in line 3 Mounted Sensor(4Cols,20um) in line 3 Changed DUT1 in line 3 to (4Cols,30um), which was dismounted from line 2. Line 3 now has (4Cols, 20um) mounted.

124

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T07:04:08+00:00

Type: Error/Fault Category: General Tags: Subject: Line2_DAQ PC connection Error Line2_DAQ PC connection Error DAQ PC connection is lost. tried restarting DAQ-PC.

125

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T07:31:08+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-20um, 125V & 4col-50um-nohole, 140V HV scan: 4col-20um, 125V & 4col-50um-nohole, 140V #Run : 111 Start : 2026-03-05-16:25:08 Stop : 2026-03-05-16:29:20 HV 1 (4col-20um) : 0.325uA (125 V)

126

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T07:29:20+00:00

Type: Error/Fault Category: General Tags: ReplyTo: 124 Subject: Re: Line2_DAQ PC connection Error Re: Line2_DAQ PC connection Error DAQ PC ssh connection : success but, we cannot run new RUN

127

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T08:25:50+00:00

Type: Error/Fault Category: General Tags: Subject: Electric power glitch on the beam area Electric power glitch on the beam area Based on the daq pc journalctl, the PC has been rebooted at 2026-03-05 15:53:25 Detailed log file is attached: Mar 05 15:52:03 msqd01 systemd[1]: Starting daq-manifest.service - EPIC DAQ Raw Manifest Generator... Mar 05 15:52:03 msqd01 env[1361673]: manifest rows=280 -> /var/www/daq-manifest/manifest.json Mar 05 15:52:03 msqd01 systemd[1]: daq-manifest.service: D…

128

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T08:30:01+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-20um, 129V(Limit voltage) & 4col-50um-nohole, 185V HV scan: 4col-20um, 129V(Limit voltage) & 4col-50um-nohole, 185V #Run : 112 Start : 2026-03-05 17:05:54 Stop : 2026-03-05-17:10:57

129

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T08:45:29+00:00

Type: General Category: Beam3_RFSoC Tags: ReplyTo: 128 Subject: Re: HV scan: 4col-20um, 129V(Limit voltage) & 4col-50um-nohole, 185V Re: HV scan: 4col-20um, 129V(Limit voltage) & 4col-50um-nohole, 185V HV scan: 4col-20um, 129V & 4col-50um-nohole, 185V

130

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T08:51:16+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-20um, 120V & 4col-50um-nohole, 175V HV scan: 4col-20um, 120V & 4col-50um-nohole, 175V HV scan: 4col-20um, 120V & 4col-50um-nohole, 175V #Run : 114 Start : 2026-03-05-17:37:09 Stop : 2026-03-05-17:17:46:39

131

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T08:53:36+00:00

Type: General Category: General Tags: Subject: Daily meeting note (3.5) Daily meeting note (3.5) * Line#2 * New alignment has been done during the night shift (MCP-PMT 100%, overall 80% coincidence) * Power glitch observed * Log1: *

132

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T09:05:01+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-20um, 115V & 4col-50um-nohole, 170V HV scan: 4col-20um, 115V & 4col-50um-nohole, 170V #Run : 115 Start : 2026-03-05-17:49:47 Stop : 2026-03-05-18:01:12 HV 1 (4col-20um) : 0.10uA (114.9V)

133

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T09:15:45+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: 4col-20um, 110V & 4col-50um-nohole, 165V 4col-20um, 110V & 4col-50um-nohole, 165V #Run : 116 Start : 2026-03-05-18:02:38 Stop : 2026-03-05-18:12:19 HV 1 (4col-20um) : 0.076uA (109.9V) HV 2 (4col-50um-nohole) : 0.16uA (164.9 V)

134

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T09:28:42+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-20um, 105V & 4col-50um-nohole, 160V HV scan: 4col-20um, 105V & 4col-50um-nohole, 160V #Run : 117 Start : 2026-03-05-18:14:52 Stop : 2026-03-05-18:24:37 HV 1 (4col-20um) : 0.06uA (104.9V)

135

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T09:40:58+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-20um, 100V & 4col-50um-nohole, 155V HV scan: 4col-20um, 100V & 4col-50um-nohole, 155V #Run : 118 Start : 2026-03-05-18:27:04 Stop : 2026-03-05-18:37:11 HV 1 (4col-20um) : 0.049uA (99.9V)

136

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T09:50:44+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-20um, 95V & 4col-50um-nohole, 150V HV scan: 4col-20um, 95V & 4col-50um-nohole, 150V #Run : 119 Start : 2026-03-05-18:39:38 Stop : 2026-03-05-18:49:05 HV 1 (4col-20um) : 0.04uA (94.9V)

137

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T10:14:00+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-20um, 90V & 4col-50um-nohole, 145V HV scan: 4col-20um, 90V & 4col-50um-nohole, 145V #Run : 120 Start : 2026-03-05-18:52:07 Stop : 2026-03-05-19:02:10 HV 1 (4col-20um) : 0.035uA (89.9V)

138

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T10:22:24+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-20um, 85V & 4col-50um-nohole, 140V HV scan: 4col-20um, 85V & 4col-50um-nohole, 140V #Run : 121 Start : 2026-03-05-19:05:53 Stop : 2026-03-05-19:15:55 HV 1 (4col-20um) : 0.03uA (85.0V)

139

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T10:39:23+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-20um, 80V & 4col-50um-nohole, 135V HV scan: 4col-20um, 80V & 4col-50um-nohole, 135V #Run : 122 Start : 2026-03-05-19:20:29 Stop : 2026-03-05-19:30:39 HV 1 (4col-20um) : 0.025uA (79.9V)

140

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T10:46:19+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-20um, 75V & 4col-50um-nohole, 130V HV scan: 4col-20um, 75V & 4col-50um-nohole, 130V #Run : 123 Start : 2026-03-05-19:33:12 Stop : 2026-03-05-19:43:58 HV 1 (4col-20um) : 0.023uA (74.9V)

141

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T11:02:30+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: 4col-20um, 0V & 4col-50um-nohole, 0V 4col-20um, 0V & 4col-50um-nohole, 0V #Run : 124 Start : 2026-03-05-19:51:14 Stop : 2026-03-05-20:00:34 HV 1 (4col-20um) : 0.07nA (0V) HV 2 (4col-50um-nohole) : 0.3nA (0 V)

142

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T13:38:21+00:00

Type: General Category: General Tags: Subject: Line2 DUT Change Line2 DUT Change Line2での4cols30umの測定が終了したため、4cols20umに変更しました

143

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T13:34:37+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: Line3 DUT Change Line3 DUT Change 4col-50um-noholeのDUTでの測定を終了し、2col-20umのDUTに変更しました。

144

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T14:20:32+00:00

Type: General Category: General Tags: ReplyTo: 143 Subject: Line2 DUT Change / trigger rate decrease Line2 DUT Change / trigger rate decrease p.s. 返信先を間違えました。Line3ではなくLine2のDUTについての経過報告です。 2cols30um

145

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T14:03:27+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-20um, 70V & 2col-20um, 125V HV scan: 4col-20um, 70V & 2col-20um, 125V #Run : 125 Start : 2026-03-05-22:27:03 Stop : 2026-03-05-22:39:19 HV 1 (4col-20um) : 0.02uA (69.9V) HV 2 (2col-20um) : 0.74uA (125.0 V)

146

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T14:18:27+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-20um, 65V & 2col-20um, 120V HV scan: 4col-20um, 65V & 2col-20um, 120V #Run : 126 Start : 2026-03-05-23:04:30 Stop : 2026-03-05-23:15:00 HV 1 (4col-20um) : 0.016uA (64.9V) HV 2 (2col-20um) : 0.41uA (120.0 V)

147

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T14:29:23+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-20um, 60V & 2col-20um, 115V HV scan: 4col-20um, 60V & 2col-20um, 115V #Run : 127 Start : 2026-03-05-23:16:32 Stop : 2026-03-05-23:26:23 HV 1 (4col-20um) : 0.014uA (59.9V) HV 2 (2col-20um) : 0.27uA (114.9V)

148

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T14:42:08+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-20um, 55V & 2col-20um, 110V HV scan: 4col-20um, 55V & 2col-20um, 110V #Run : 128 Start : 2026-03-05-23:28:08 Stop : 2026-03-05-23:37:54 HV 1 (4col-20um) : 0.011uA (54.9V) HV 2 (2col-20um) : 0.20uA (109.9V)

149

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T14:56:20+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-20um, 50V & 2col-20um, 105V HV scan: 4col-20um, 50V & 2col-20um, 105V #Run : 130 Start : 2026-03-05-23:42:23 Stop : 2026-03-05-23:52:17 HV 1 (4col-20um) : 0.006uA (50.0V) HV 2 (2col-20um) : 0.16uA (104.9V)

150

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T15:09:20+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-20um, 45V & 2col-20um, 100V HV scan: 4col-20um, 45V & 2col-20um, 100V #Run : 131 Start : 2026-03-05-23:54:44 Stop : 2026-03-05-00:05:04 HV 1 (4col-20um) : 0.003uA (45.0V) HV 2 (2col-20um) : 0.12uA (100.0V)

151

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T15:21:34+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-20um, 40V & 2col-20um, 95V HV scan: 4col-20um, 40V & 2col-20um, 95V #Run : 132 Start : 2026-03-05-00:06:44 Stop : 2026-03-05-00:16:53 HV 1 (4col-20um) : 0.003uA (39.9V) HV 2 (2col-20um) : 0.11uA (95.0V)

152

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T15:32:48+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-20um, 35V & 2col-20um, 90V HV scan: 4col-20um, 35V & 2col-20um, 90V #Run : 133 Start : 2026-03-05-00:19:24 Stop : 2026-03-05-00:29:11 HV 1 (4col-20um) : 0.002uA (34.9V) HV 2 (2col-20um) : 0.09uA (89.9V)

153

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T15:52:15+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-20um, 30V & 2col-20um, 85V HV scan: 4col-20um, 30V & 2col-20um, 85V #Run : 134 Start : 2026-03-05-00:30:56 Stop : 2026-03-05-00:41:16 HV 1 (4col-20um) : 0.002uA (30.0V) HV 2 (2col-20um) : 0.08uA (84.9V)

154

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T16:03:34+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-20um, 25V & 2col-20um, 80V HV scan: 4col-20um, 25V & 2col-20um, 80V #Run : 135 Start : 2026-03-05-00:46:08 Stop : 2026-03-05-00:56:02 HV 1 (4col-20um) : 0.002uA (30.0V) HV 2 (2col-20um) : 0.07uA (84.9V)

155

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T16:09:01+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV scan: 4col-20um, 20V & 2col-20um, 75V HV scan: 4col-20um, 20V & 2col-20um, 75V #Run : 137 Start : 2026-03-05-00:57:25 Stop : 2026-03-05-01:07:25 HV 1 (4col-20um) : 0.001uA (30.0V) HV 2 (2col-20um) : 0.07uA (84.9V)

156

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T21:53:53+00:00

Type: General Category: Setup Tags: Subject: Reset alignment at 0mm point (40cols, 20um) Reset alignment at 0mm point (40cols, 20um) * 2026/03/06-02:09にて、DUT-0mmの時のStageの再設定を行った。 * Stage Controller内の適切な0mm地点は絶対座標で

157

Anonymous (anonymous@undisclosed.example.com) — 2026-03-05T22:03:22+00:00

Type: General Category: Setup Tags: Subject: Reset alignment at 0mm point (40cols, 50um) Reset alignment at 0mm point (40cols, 50um) * 2026/03/06-06:51にて、DUT-0mmの時のStageの再設定を行った。 * Stage Controller内の適切な0mm地点は絶対座標で67688 (@Axis2)とした。

158

Anonymous (anonymous@undisclosed.example.com) — 2026-03-06T15:15:12+00:00

Type: Shift Summary Category: Beam3_RFSoC Tags: Subject: HV scan: 3/6 1:00-8:30 HV scan: 3/6 1:00-8:30 DUT1 : 4col-20um 20V, DUT2 2col-20um 75V RUN | HV1 | I1 | HV2 | I2 | time | events | rate | comments 137 | 70V | - | 70V | - | 15m11s | 150612 | 165Hz | forget to check I

159

Anonymous (anonymous@undisclosed.example.com) — 2026-03-06T04:23:09+00:00

Type: Shift Summary Category: Beam3_RFSoC Tags: Subject: RFSoC Run Table (temporary) RFSoC Run Table (temporary) run DUT1 HV1 [V] I1 [uA] DUT2 HV2 [V] I2 [uA] start end time events rate [Hz] comment 41 2col 30um -185 586,000

160

Anonymous (anonymous@undisclosed.example.com) — 2026-03-06T01:00:51+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: 3/6 シフターやることリスト 3/6 シフターやることリスト * 2026-03_raris:159 のelogを参照しながら、データ量の少なそうな箇所を補う (最低100k events, 適宜増やす)

161

Anonymous (anonymous@undisclosed.example.com) — 2026-03-06T01:04:38+00:00

Type: General Category: Beam3_RFSoC Tags: ReplyTo: 45 Subject: Re: RFSoC channel and DUT sensor channel correspondence Re: RFSoC channel and DUT sensor channel correspondence 画像が正しく表示されていないようなので再送

162

Anonymous (anonymous@undisclosed.example.com) — 2026-03-06T08:35:58+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV Scan: 3/6 8:3011:49 ====== HV Scan: 3/6 8:3011:49 DUT1 : 4col-20um, DUT2 2col-20um RUN | HV1 | I1 | HV2 | I2 | start | stop | time | events | rate | comments 151 | -127V | -0.481 uA | -126.706V | -1 uA | 06-Mar-26 08:56:59 | 06-Mar-26 10:51:22 | 114m 23s | 1,002,169 | 146 Hz |

163

Anonymous (anonymous@undisclosed.example.com) — 2026-03-06T03:32:35+00:00

Type: General Category: General Tags: Subject: Line 2 DUT cable mismatch Line 2 DUT cable mismatch Channel 2 cable is shorter than the rest, will need to measure after run is done (see pic) This was also seen in the data, time difference of ~500ps for ch2

164

Anonymous (anonymous@undisclosed.example.com) — 2026-03-06T03:33:44+00:00

Type: General Category: General Tags: Subject: new DUT il line 2 new DUT il line 2 Changed DUT in line 2, mounted 2col 30um, HV set at 197V

165

Anonymous (anonymous@undisclosed.example.com) — 2026-03-06T03:49:18+00:00

Type: General Category: Setup Tags: Subject: The beam target changed (same material but thicker one) -> beam rate increased The beam target changed (same material but thicker one) -> beam rate increased We expect around 2 times more, but for the moment, we're observing ~4 Hz.

166

Anonymous (anonymous@undisclosed.example.com) — 2026-03-06T03:51:01+00:00

Type: General Category: General Tags: Subject: The first safety key disabled (beam area) The first safety key disabled (beam area) The first safety key has been lost by manager (not our fault) -> temporary disabled. Please contact him (Tokiyasu-san) if we can find the key in the beam area

167

Anonymous (anonymous@undisclosed.example.com) — 2026-03-06T03:52:10+00:00

Type: Error/Fault Category: General Tags: ReplyTo: 163 Subject: Re: Line 2 DUT cable mismatch Re: Line 2 DUT cable mismatch Next time, the length of the cable, especially for the DUT has to be same for all channels.

168

Anonymous (anonymous@undisclosed.example.com) — 2026-03-06T04:26:12+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: LINE3 DUT Change LINE3 DUT Change 2列20umのセンサーを4列50um(穴なし)に変更しました

169

Anonymous (anonymous@undisclosed.example.com) — 2026-03-06T04:30:15+00:00

Type: General Category: Setup Tags: ReplyTo: 165 Subject: Re: The beam target changed (same material but thicker one) -> beam rate increased Re: The beam target changed (same material but thicker one) -> beam rate increased the number of segements updated from 100 to 500.

170

Anonymous (anonymous@undisclosed.example.com) — 2026-03-06T04:38:04+00:00

Type: General Category: General Tags: Subject: Line2: Changed the number of segments acquired from 100 to 500 Line2: Changed the number of segments acquired from 100 to 500 取得セグメント数を100から500に変更しました

171

Anonymous (anonymous@undisclosed.example.com) — 2026-03-06T05:22:48+00:00

172

Anonymous (anonymous@undisclosed.example.com) — 2026-03-06T08:35:33+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV Scan: 3/6 12:5317:33 ====== HV Scan: 3/6 12:5317:33 DUT1 : 4col-20um, DUT2 4col-50um (nohole) RUN | HV1 | I1 | HV2 | I2 | start | stop | time | events | rate | comments 153 | -125V | -0.328 uA | -190V | -0.369 uA | 06-Mar-26 12:53:48 | 06-Mar-26 13:26:31 | 32m 43s | 473,825 | 242 Hz |

173

Anonymous (anonymous@undisclosed.example.com) — 2026-03-06T09:10:42+00:00

Type: General Category: General Tags: Subject: Daily meeting note (3.6) Daily meeting note (3.6) * Line#2 * 4col-20um -> decide to not take 20um data * 2col/4col 50/30um data are taken well * Next plan -> Simon's plan (add one more DUT for the additional tracking layer) ~

174

Anonymous (anonymous@undisclosed.example.com) — 2026-03-06T10:46:46+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: HV Scan: 3/6 17:00~ HV Scan: 3/6 17:00~ DUT1 : 4col-20um, DUT2 4col-50um (nohole) \ RUN | HV1 | I1 | HV2 | I2 | start | stop | time | events | rate | comments 161 | -90V | -0.363 uA | -150V | -0.123 uA | 06-Mar-26 17:33:55 | 06-Mar-26 18:00:17 | 26m 22s | 405,425 | 256 Hz |

175

Anonymous (anonymous@undisclosed.example.com) — 2026-03-06T11:39:11+00:00

Type: General Category: General Tags: Subject: Line 2 double DUT setup Line 2 double DUT setup Changed DUT to double DUT in line one Sensor front: 2col 50um, horizontal strips, 185V Sensor back: 2col 30um, vertical strips, 197V

176

Anonymous (anonymous@undisclosed.example.com) — 2026-03-06T15:47:07+00:00

Type: General Category: Beam3_RFSoC Tags: Subject: pixel-type AC-LGAD : 3/6 20:30~ pixel-type AC-LGAD : 3/6 20:30~ DUT1 : pixel-type AC-LGAD(W7 big ), DUT2 none RUN | HV1 | I1 | HV2 | I2 | start | stop | time | events | rate | comments 166 | -140 | -0.746uA | — | — | 06-Mar-26 20:23:00 | 06-Mar-26 20:37:46 | 14m 46s | 127,863 | 144 Hz |

177

Anonymous (anonymous@undisclosed.example.com) — 2026-03-06T16:05:07+00:00

Type: General Category: General Tags: Subject: Beam 周期変更 Beam 周期変更ビーム周期が、10sON-20sOFF の30s から10sON-17sOFFの27s に変更されました

178

Anonymous (anonymous@undisclosed.example.com) — 2026-03-06T16:20:03+00:00

Type: General Category: Beam3_RFSoC Tags: ReplyTo: 176 Subject: Re: pixel-type AC-LGAD : 3/6 20:30~ Re: pixel-type AC-LGAD : 3/6 20:30~ Run 174 を動かしたまま、一晩放置します

179

Anonymous (anonymous@undisclosed.example.com) — 2026-04-24T05:02:02+00:00

Type: General Category: Beam3_RFSoC Tags: ReplyTo: 161 Subject: Re: RFSoC channel and DUT sensor channel correspondence Re: RFSoC channel and DUT sensor channel correspondence Board1 row1-8: rfsoc1 ch0 Board1 row1-6: rfsoc1 ch1 Board1 row1-4: rfsoc1 ch2

start

Anonymous (anonymous@undisclosed.example.com) — 2026-02-27T12:44:48+00:00

2026-03 RARiS Link to General information of the test beam campagin Shared album